產品
Semi-Automatic Dip Soldering Machine — FD700 Series (Microcontroller Type)
- 產品詳情
-
SEMI-AUTOMATIC SERIES · SEMI-AUTOMATIC DIP SOLDERING MACHINE (FD700 · MICROCONTROLLER TYPE)
The FD700 series is a Semi-Automatic Dip Soldering Machine for transformer, magnetic-ring, inductor, straight-pin and special-shaped-pin parts. The operator loads the fixture and the microcontroller runs the dip cycle, so the up/down stroke, the dwell time and the scraper sequence are the same on every part. Six functions can be combined on the same platform — up/down, solder scraper, translation (inclined), solder cup, jump and left lift — which gives nine delivered build-ups from FD-700 up to FD763. Solder pot 300 × 100 × 50 mm, 1400 W. Built to order by FD in Dongguan, Guangdong, China. In the trade the same machine is also called a semi-automatic tin dipping machine, a semi-automatic solder pot machine or a semi-automatic tinning machine — all these names refer to the same machine.
Product ParametersModel FD700 series — FD-700 / FD701 / FD703 / FD711 / FD712 / FD713 / FD761 / FD762 / FD763 Also Known As Semi-Automatic Dip Soldering Machine · Semi-Automatic Tin Dipping Machine · Semi-Automatic Solder Pot Machine Control Microcontroller control · semi-automatic dip cycle Functions Up/down · solder scraper · translation (inclined) · solder cup · jump · left lift Solder Pot 300 × 100 × 50 mm Power 1400 W Weight 8 kg Delivered Build-Ups 9 combinations, from up/down only to up/down + scraper + cup + translation + left lift + jump Suitable Products Transformers, magnetic rings, inductors, straight-pin & special-shaped-pin parts Specifications are as listed in our catalogue. Fixtures and tooling are made to your part drawing — send us a sample part for a proposal.
Function SetUp/down — the head lowers the fixture into the pot and lifts it out on a fixed stroke, so the dipped length is the same on every part
Solder scraper (tin knife) — skims the oxide skin off the solder surface, so the pins meet clean solder instead of dross
Translation (inclined) — moves the fixture sideways as it leaves the pot; the inclined version keeps the exit angle low to reduce solder build-up
Solder cup — brings solder up to a pin group from below, for parts that stand upright in the fixture
Jump — steps to a second pin group inside one cycle, so one program covers a part with several rows of pins
Left lift — raises the head to the left side of the pot, for parts or fixtures that cannot come straight up
Microcontroller control — the dip cycle is run by the controller, so the operator only loads and unloads and the same cycle repeats for the whole batch
Fixture made to your part — brackets and tooling are made from your drawing or sample
The six functions are combined per model — for example FD-700 is up/down only, while FD763 adds the scraper, the left lift and the jump. Tell us your soldering sequence and we will quote the matching build-up.
Product OverviewApplication FieldsTransformer Pin Soldering
Magnetic-Ring & Inductor Leads
Straight & Special-Shaped Pins
Multi-Model, Small-Batch Lines
FeaturesMicrocontroller Control
Solder Pot 300 × 100 × 50 mm
Up/Down · Scraper · Translation
Solder Cup / Jump / Left Lift Options
AdvantagesSame Dip Depth on Every Part
9 Build-Ups on One Platform
Operator Only Loads and Unloads
Factory Direct from Dongguan, China
Semi-Automatic Dip Soldering Machine RangeThe Semi-Automatic Dip Soldering Machine range covers microcontroller machines, bracket-and-pot sets and solder cup sets. Every set is built to order in Dongguan, Guangdong, China — send us your part, pin layout and output per shift for a machine recommendation and quotation.
Product Details
FD700 series overall view

Working position

Configuration detail
Photographs are of the standard model. Fixtures are adapted to your part.
Product Demo Video
▶ Watch the working video →
Application ScenariosTransformer & Inductor Pins Transformer, magnetic-ring and inductor leads are dipped in one fixture load, with the up/down stroke set once for the batch. Multi-Model, Small-Batch Lines Nine build-ups on one platform: a workshop soldering several part numbers a day picks the function set that matches the hardest part and runs the rest on the same machine. Without a Full-Time Soldering Engineer The dip cycle is held by the controller instead of by hand, so any operator can load, dip and unload with the same result. Even Coverage on Awkward Pins Inclined translation, the solder cup and the left lift cover straight, special-shaped and upright pin groups that a plain vertical dip leaves uneven. How To UseLoad the fixture with your transformer, magnetic ring or pin part — the platform height is set once for the batch.
Apply flux to the pin group before the part travels to the pot.
Start the stored cycle the microcontroller runs the scraper, the dip and the lift in the same order every time.
Let the scraper work first it skims the oxide skin so the pins enter clean solder rather than dross.
Unload and repeat the same stroke and dwell apply to the whole batch, so the dipped length does not drift.
Keep the pot topped up and skimmed so the solder surface stays clean through the shift.
⚠ Safety notice: molten solder operates at high temperature — never reach into the pot area while the machine runs, keep the work area dry (molten solder and water contact can cause splatter), use heat-resistant gloves during pot maintenance, and isolate the power supply before any service.Frequently Asked QuestionsQ1: What is a Semi-Automatic Dip Soldering Machine?
It is a machine that dips component pins into molten solder with the dip cycle held by the machine and the loading and unloading done by an operator. On the FD700 series the head motion is run by a microcontroller, so the stroke and dwell are the same on every part. The same machine is also called a semi-automatic tin dipping machine, a semi-automatic solder pot machine or a semi-automatic tinning machine — all these names refer to the same machine.
Q2: What does "semi-automatic" mean here?
The operator loads the fixture and starts the cycle; the machine then runs the scraper, the dip and the lift on a stored setting. Compared with hand dipping the dipped length stops depending on the operator's hand, and compared with a full automatic line there is no conveyor or robot loading station to pay for.
Q3: How do I choose between the FD700 models?
By the functions your part needs. FD-700 is up/down only; FD701 adds the solder scraper; FD703 uses the scraper with translation; FD711, FD712 and FD713 add the solder cup; FD761 adds the jump; FD762 combines the left lift with a double jump; FD763 combines the scraper with the left lift and the jump. Send us a sample part and we will name the exact build-up.
Q4: What are the solder pot size and the power rating?
The solder pot measures 300 × 100 × 50 mm and the machine is rated 1400 W, with a machine weight of 8 kg. Pot size, voltage and fixture can be adapted if your part needs a different dipping area.
Q5: Can the fixture be made for my part?
Yes. The machine is built to order in Dongguan, Guangdong, China, and the brackets and tooling are made to your part drawing. Send us your part, pin layout and output per shift and we will propose the configuration and quotation.
Q6: Which industries use a Semi-Automatic Dip Soldering Machine like this?
Transformer, magnetic-ring inductor and SMD makers, plus any workshop soldering straight-pin or special-shaped-pin parts in batches — wherever leads must be dip-soldered with repeatable results and the volume does not justify a full automatic line.
Need repeatable pin dipping without a full automatic line?OEM / ODM available · Microcontroller control · Solder pot 300 × 100 × 50 mm · 1400 W · Up/down · scraper · translation · cup · jump · left lift · Factory direct from Dongguan, China · Fixture drawing on requestGet a Quote
相關產品
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
Ultrasonic solder pot FD-20014070C, 200x...
Ultrasonic Solder Pot FD-14014070C | Flux-Free Tinning Machine 140x140 mm Bath
Ultrasonic solder pot FD-14014070C, 140x...
Ultrasonic Solder Pot FD-12012060C | Flux-Free Tinning Machine 120x120 mm Bath
Ultrasonic solder pot FD-12012060C, 120x...
Stainless Steel Explosion-Proof Industrial Oven FD1200800800FBB
Stainless Steel Explosion-Proof Industri...
產品詢價
請留言,我們收到後會迅速與您聯繫,感謝您的支持!
常見問題
問
香菸盒三維包裝機特點?
答
1. 更換模具時無需調節機器兩側工作臺面高度,無需拆裝出料鏈條、放料斗,將傳統機四小時的更換模具時間縮短爲只需現在30分鐘。
2. 採用新式雙保險機構,機器運行不同步時無需停機也不會損壞其它零部件。
3. 獨創的單向手搖裝置防止逆向搖動機器,且運行時手輪不會轉動使操作人員更安全。
4. 新型雙旋轉切膜刀可保證機器連續使用多年無需磨刀口,克服了傳統固定式單旋轉切膜刀刃容易磨損的缺陷。
問
全自動撲克透明膜三維包裝機包裝產品?
答
全自動撲克透明膜三維包裝機主要適用於散裝撲克、壓縮餅乾,沙琪瑪、報事貼、便箋紙、威化餅乾等散狀或多件物體集合的三維包裝。
English
繁体中文
简体中文
Deutsch
Tiếng Việt


