Products
Heating-Type Enamel Stripping Machine
- Product details
-
Wire Peeling Series · Luoyiyun · Dongguan, ChinaHEATING-TYPE ENAMEL STRIPPING MACHINE · Hot copper block · up to 450 °C
The Heating-Type Enamel Stripping Machine is a bench-top unit that takes the insulation off wire ends by contact: a copper heating block, 150 × 60 × 25 mm, is held at up to 450 °C by a digital controller, and the wire end pressed on the block loses its enamel, varnish or lacquer film in seconds — no blades, no chemicals and no scraped copper. The controller sits beside the block in a split design, with a PV / SV display, SET keys and a power switch. Also listed as a heated enamel stripping block or a thermal magnet wire stripper.
Product ParametersModel Heating-Type Enamel Stripping Machine Product Type Heating-type wire stripping machine (hot block) Also Known As Heated enamel stripping block / thermal magnet wire stripper Heating Block Copper, 150 × 60 × 25 mm Max Temperature 450 °C Temperature Control Digital PV / SV controller with SET keys, run / stop buttons and power switch (as pictured) Design Split unit — hot block on insulated base, controller connected by cable Power Supply Quoted against your order (controller nameplate is filled in per unit) Place of Origin Dongguan, China Selling Unit 1 set — heating block + temperature controller Block size and controller configuration can be customized. Contact us for the full datasheet.
Function SetCopper heating block, 150 × 60 × 25 mm — a flat working face with room for several wire ends at once.
Up to 450 °C — hot enough to burn off enamel, varnish and lacquer films.
Digital PV / SV controller — set the working temperature and watch the actual value stabilize before you strip.
Split design — the hot block stays on the bench while the controller and power switch sit within reach.
No blades, no consumables — the film burns off; nothing to regrind, sharpen or replace.
Copper working face — spreads heat evenly across the block for a consistent strip.
Product OverviewApplication FieldsEnameled / magnet wire ends
High-temperature wire
Triple-insulated wire
Repair & sample work
FeaturesMax block temperature 450 °C
Copper block 150 × 60 × 25 mm
Digital PV / SV control
Split controller design
AdvantagesClean copper after stripping — no nicks
No blade stock, no chemicals
Burn-off process, no solvents
Factory direct from Dongguan
Enamel Stripping Machine RangeProduct Details
Block + controller, working

Full set, front view

Copper block on insulated base

Heater element & wiring detail
Product Demo VideoProduct
Demo VideoVideo slot reserved — the clip is published here as soon as it is filmed.
Application ScenariosMagnet wire before soldering — strip on the block, then tin in a solder pot; the two steps pair naturally.
Repair & sample work — single ends and short runs where setting up a blade machine is not worth it.
Plated or fragile conductors — burn-off leaves no tool marks, so tinned or thin copper ends stay intact.
High-temperature & lacquered wire — varnish and lacquer films that resist scraping burn off cleanly.
How To UsePlace the block on a dry, insulated surface and connect the controller cable.
Set the target temperature with the SET / up / down keys; wait for the PV value to stabilize.
Press the wire end on the block face and rotate it until the film burns off evenly.
Brush the residue off the end; for triple-insulated wire a second short pass gives a clean copper surface.
Tin or use the end as your process requires.
Switch off and let the block cool before cleaning or storing the unit.
⚠ Safety notice: the block reaches 450 °C — never touch it during or immediately after operation. Burning insulation gives off fumes, so keep bench ventilation on, wear safety glasses, and disconnect the power before moving the unit.FAQQ1: Heating block or blade type — which one suits my line?
A: The blade-type FD-305 scrapes the film off mechanically and suits batch work at a fixed length. The heated block burns the film off and suits repair, samples and ends where the copper must not be scraped. Many benches keep one of each.
Q2: What temperature should I set?
A: Set it against your film — start low and raise until the film burns off cleanly. The block is rated to 450 °C max, which covers common enamel, varnish and lacquer films.
Q3: Will the heat damage the copper?
A: No tool touches the wire, so the copper is left clean and un-nicked; only the insulation film burns away. Brush off the light residue before tinning.
Q4: Can the block be made in another size?
A: The stocked block is 150 × 60 × 25 mm copper. Other block sizes and controller configurations can be made against your order.
Q5: Does it need blades or spare parts?
A: No blades and no consumables — the film burns off. There is nothing to regrind or replace in normal use.
Q6: What about fumes and lead time?
A: Burning insulation gives off fumes, so run bench ventilation. Stock sets ship in 3 – 7 days; customized blocks are quoted separately.
Need clean wire ends without blades?OEM / ODM available · Custom block sizes · Factory direct from Dongguan, China · Sample testing supportedGet a Quote
related products
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
Ultrasonic solder pot FD-20014070C, 200x...
Ultrasonic Solder Pot FD-14014070C | Flux-Free Tinning Machine 140x140 mm Bath
Ultrasonic solder pot FD-14014070C, 140x...
Ultrasonic Solder Pot FD-12012060C | Flux-Free Tinning Machine 120x120 mm Bath
Ultrasonic solder pot FD-12012060C, 120x...
Stainless Steel Explosion-Proof Industrial Oven FD1200800800FBB
Stainless Steel Explosion-Proof Industri...
Product Inquiry
Please leave your message, we will contact you quickly after receiving it, thank you for your support!
common problem
Q
What are the characteristics of cigarette box three-dimensional packaging machine?
A
1. There is no need to adjust the height of the countertops on both sides of the machine when changing the mold, and there is no need to disassemble and assemble the discharge chain or put the hopper, which shortens the four-hour mold replacement time of the traditional machine to only 30 minutes.
2. Adopting a new dual insurance mechanism, the machine does not need to be shut down when it is not running synchronously, nor will it damage other parts.
3. The original one-way hand crank device prevents the machine from shaking in reverse, and the handwheel does not rotate during operation, making the operator safer.
4. The new double rotary film cutting knife can ensure that the machine can be used continuously for many years without a sharpening port, overcoming the defect that the traditional fixed single rotary film cutting blade is easy to wear.
Q
Automatic poker transparent film three-dimensional packaging machine packaging products?
A
Automatic poker transparent film three-dimensional packaging machine is mainly suitable for bulk poker, compressed biscuits, sachima, stickers, sticky notes, wafer biscuits and other bulk or multi-object collection of three-dimensional packaging.
E-mail address:
Hotline:
English
繁体中文
简体中文
Deutsch
Tiếng Việt
