Products
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
- Product details
-
ULTRASONIC SOLDER POT · FD-20014070C (FLUX-FREE TINNING · 200 × 140 mm BATH)
The Ultrasonic Solder Pot FD-20014070C is the largest bath in the series: a flux-free tinning and dip-soldering machine for magnet wire, inductor and transformer pins, and the difficult dissimilar materials that flux tinning simply cannot wet. A 20 kHz transducer drives cavitation straight into the molten solder, so the oxide film is stripped mechanically and the base metal is wetted without any flux at all. The 200 × 140 mm bath is built for long busbars, wide connector blocks and high-volume tinning runs where the smaller models would need several dips. Also listed as an ultrasonic tinning machine, a flux-free solder pot or ultrasonic dip soldering equipment.
Product ParametersModel FD-20014070C — Ultrasonic Solder Pot Also Known As Ultrasonic Tinning Machine · Ultrasonic Dip Soldering Equipment · Flux-Free Solder Pot Bath size 200 × 140 mm (bath depth 70 mm per model code) Ultrasonic power 1000 W Heating power 1800 W Ultrasonic frequency 20 kHz Voltage 220 V / 50 Hz Solder capacity 16 kg (36 kg bath option quoted on request) Machine weight 28 kg Overall size 740 × 250 × 180 mm Pot material 304 stainless steel Horn material Titanium alloy Carton size Quoted against your order Packing quantity 1 unit per carton Rows are transcribed from the parameter fields recorded on the listing for the ultrasonic solder pot series. Rows marked "Quoted against your order" are confirmed with the quotation.
Function SetFlux-free ultrasonic tinning — 20 kHz cavitation in the molten solder strips oxide off the work piece, so the alloy wets bare copper, aluminium and enamel wire with no flux at all.
Largest 200 × 140 mm bath — the biggest immersion zone in the series, sized for long busbars, wide connector blocks and high-volume runs.
Enamel removal in one dip — polyurethane and polyester enamel on magnet wire is burned off and the copper tinned in the same pass, replacing a separate stripping step.
1000 W ultrasonic transducer — sustained cavitation energy spread across the full bath area, so throughput rises without changing the process recipe.
1800 W heating with digital control — the larger melt volume holds its working temperature under load, so the wetting result stays consistent across the batch.
Dissimilar-material joining — aluminium–copper, aluminium–glass and aluminium–ceramic connections that conventional soldering cannot make.
Product OverviewApplication Fields Features Advantages Long busbar and copper-bar tinning, wide connector block and multi-pin header tinning, inductor and transformer pin tinning, magnet and enamelled wire tinning, solar photovoltaic glass sealing, semiconductor and ceramic heater work. 1000 W ultrasonic power, 1800 W heating, 20 kHz, 16 kg solder capacity, 200 × 140 mm bath, 304 stainless steel pot, titanium alloy horn, 220 V / 50 Hz, 28 kg. Biggest immersion zone in the series, so long parts go in one dip instead of several; no flux, so no residue to wash off, no flux pitting and no acid waste water. Ultrasonic Solder Pot RangeAll three models share the same transducer platform, 304 stainless steel pot and titanium alloy horn — the model number is the bath size in millimetres.
Product Details
Overall view with the 200 × 140 mm bath

20 kHz transducer head and titanium alloy horn

Control panel and 304 stainless steel pot body
Photographs are the current listing images for the ultrasonic solder pot series.
Product Demo Video
Watch the flux-free tinning process
The clip shows the transducer running in the molten bath and parts being dipped with no flux applied at any stage.
▶ Play the video
Application ScenariosLong busbars Copper and aluminium busbars that are too long for the smaller baths are tinned along their whole length in a single immersion. Wide connector blocks Multi-pin headers, terminal blocks and wide connector bodies sit across the 200 mm dimension, so every pin is wetted in the same pass. High-volume tinning Production lines that would otherwise run several dips per batch use the full bath area to cut the number of immersions. Aluminium & dissimilar metals Aluminium to copper, glass and ceramic connections that ordinary flux soldering cannot wet, plus glass sealing and ceramic heater terminals. How To UseSettle the machine on a level bench, connect the 220 V / 50 Hz supply, and charge the 304 stainless steel pot with up to 16 kg of solder.
Switch on the 1800 W heating and let the bath reach the working temperature for your alloy — around 250–270 °C for lead-free SAC solder.
Start the 1000 W ultrasonic transducer and let the cavitation settle across the full 200 × 140 mm area.
Immerse the work piece along its full length — no flux is applied at any stage. Long parts go in one dip across the 200 mm dimension.
Withdraw slowly, let the joint cool, and inspect — a flux-free joint shows no residue and needs no cleaning step.
Between batches, skim the bath surface and top up the solder; at the end of the shift switch off the transducer first, then the heater.
Safety note: molten solder at 250–400 °C causes severe burns. Wear heat-resistant gloves and a face shield, keep water and damp parts away from the bath entirely, work under extraction, and never start the transducer before it is submerged in the melt.
FAQQ1: What is an ultrasonic solder pot used for?
A: Flux-free tinning and dip soldering. The 20 kHz transducer creates cavitation in the molten solder that mechanically strips the oxide layer, so magnet wire, inductor and transformer pins, aluminium, glass and ceramic can be wetted — jobs conventional flux tinning cannot do.
Q2: Why choose the 200 × 140 mm model?
A: For long or wide work pieces and high-volume runs. Busbars and long pin rows that would need several dips in a smaller bath go in once, so cycle time falls without changing the process recipe.
Q3: Do I still need flux or a cleaning line?
A: No. Ultrasonic cavitation removes the oxide film physically, so no flux is required — and that means no flux residue to wash off, no flux pitting on the joint, no acid waste water and no consumable flux cost.
Q4: Can it remove enamel from magnet wire?
A: Yes. Polyurethane and polyester enamel on magnet wire is burned off and the copper tinned in the same dip, so a separate stripping step is no longer needed.
Q5: What materials can be joined?
A: Aluminium to copper, aluminium to glass, aluminium to ceramic, and enamelled or oxidised copper — combinations conventional flux soldering cannot wet. The process also suits inductor and transformer pins, busbars and precision pre-tinning.
Q6: How do I get a price and lead time?
A: Send us your work piece size and material, the solder alloy, the required bath size and your supply voltage. Carton size and the final configuration are quoted against your exact order, so our sales engineer confirms them together with the price and lead time.
Need a quotation for the Ultrasonic Solder Pot FD-20014070C?
Send us your work piece size and solder alloy — we confirm the bath size, voltage and lead time with the quotation.
Get a Quote
related products
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
Ultrasonic solder pot FD-20014070C, 200x...
Ultrasonic Solder Pot FD-14014070C | Flux-Free Tinning Machine 140x140 mm Bath
Ultrasonic solder pot FD-14014070C, 140x...
Ultrasonic Solder Pot FD-12012060C | Flux-Free Tinning Machine 120x120 mm Bath
Ultrasonic solder pot FD-12012060C, 120x...
Stainless Steel Explosion-Proof Industrial Oven FD1200800800FBB
Stainless Steel Explosion-Proof Industri...
Product Inquiry
Please leave your message, we will contact you quickly after receiving it, thank you for your support!
common problem
Q
What are the characteristics of cigarette box three-dimensional packaging machine?
A
1. There is no need to adjust the height of the countertops on both sides of the machine when changing the mold, and there is no need to disassemble and assemble the discharge chain or put the hopper, which shortens the four-hour mold replacement time of the traditional machine to only 30 minutes.
2. Adopting a new dual insurance mechanism, the machine does not need to be shut down when it is not running synchronously, nor will it damage other parts.
3. The original one-way hand crank device prevents the machine from shaking in reverse, and the handwheel does not rotate during operation, making the operator safer.
4. The new double rotary film cutting knife can ensure that the machine can be used continuously for many years without a sharpening port, overcoming the defect that the traditional fixed single rotary film cutting blade is easy to wear.
Q
Automatic poker transparent film three-dimensional packaging machine packaging products?
A
Automatic poker transparent film three-dimensional packaging machine is mainly suitable for bulk poker, compressed biscuits, sachima, stickers, sticky notes, wafer biscuits and other bulk or multi-object collection of three-dimensional packaging.
E-mail address:
Hotline:
English
繁体中文
简体中文
Deutsch
Tiếng Việt

