Produkte
Ceramic Heater Type Lead-Free Solder Pot
- Details zum Produkt
-
CERAMIC SERIES · CERAMIC HEATER TYPE LEAD-FREE SOLDER POT (CERAMIC HEATING TUBE)
The ceramic-heater type Lead-Free Solder Pot is a bench-top solder pot for hand dipping and tinning: the operator holds the part and dips it into molten solder, so it suits repair work, small batches and mixed part numbers. The pot body is titanium alloy, which resists the aggressive corrosion that lead-free solder causes in cast iron and plain stainless steel, and the heater is a ceramic heating tube rated 500 - 2000 W. Running temperature is set with stepless inverter control on 110 - 220 V / 50 Hz, and the housing is 201 stainless steel. Sizes run from 80 × 80 × 50 mm up to 400 × 135 × 50 mm, with a 40 × 40 mm dross box and a 90 × 60 × 50 mm wiring box; larger sizes are made to order. Built by FD in Dongguan, Guangdong, China. In the trade the same pot is also called a lead-free soldering pot, a lead-free solder bath or a lead-free tin pot — all these names refer to the same pot.
Product ParametersModel Ceramic heater type — 12 stock sizes, further sizes built to order Also Known As Lead-Free Solder Pot · Lead-Free Soldering Pot · Lead-Free Solder Bath · Lead-Free Tin Pot Heater Ceramic heating tube Pot Material (inner) Titanium alloy Housing (outer) 201 stainless steel Power 500 - 2000 W (according to pot size) Voltage 110 - 220 V / 50 Hz Temperature Control Inverter (stepless) temperature control Pot Core Treatment 800 °C high-temperature treatment Dross Box 40 × 40 mm, same width as the pot Wiring Box 90 × 60 × 50 mm Outer Dimensions Inner size + 130 mm length, + 40 mm width, + 50 mm height Pot Core Allowance + 24 mm × 2 on the long sides, + 18 mm × 2 on the short sides Warranty Heating element 3 months, other parts 1 year Stock Sizes (inner, L × W × D mm) 80×80×50 · 100×100×50 · 200×80×50 · 240×80×50 · 280×80×50 · 300×100×50 · 320×120×60 · 350×100×50 · 350×120×90 · 290×90×85 · 400×135×50 · 160×75×67 Specifications are as listed in our catalogue. Any other pot size is built to order — send us the inner length, width and depth you need for a quotation.
Feature SetTitanium alloy pot — titanium resists the corrosion that lead-free (SAC) solder causes in cast iron and plain stainless steel pots, so the pot lasts far longer on lead-free work
Ceramic heating tube — the heater is a ceramic-type heating tube held against the pot wall, giving even heat across the pot floor instead of a hot spot under one spot
Stepless inverter control — set the running temperature on the dial and the controller holds it; no fixed steps between low and high
201 stainless steel housing — protects the heater and the insulation and keeps the outer shell cool enough to handle
Dross box 40 × 40 mm — a separate pocket, the same width as the pot, where the oxide skin is pushed so it does not sit on the working surface
Wiring box 90 × 60 × 50 mm — keeps the power lead and the thermocouple away from the solder area
Pot size to your drawing — 12 stock sizes, and any other length, width or depth is made to order
Warranty — heating element 3 months, other parts 1 year
Tell us the parts you tin and the pot size you need, and we will quote the matching ceramic-heater pot.
Product OverviewApplication FieldsWire & Cable End Tinning
Transformer & Inductor Pins
Terminal & Lug Dipping
Repair & Rework Benches
FeaturesTitanium Alloy Pot
Ceramic Heating Tube
500 - 2000 W · 110 - 220 V
12 Stock Sizes, More to Order
AdvantagesLong Pot Life on Lead-Free Solder
Even Heat, No Hand-Held Torch
Dross Kept Out of the Working Area
Factory Direct from Dongguan, China
Lead-Free Solder Pot RangeThe Lead-Free Solder Pot range covers the ceramic heater type, the high-temperature heating-tube type, the oil-resistant ceramic type, the flat-plate type and replacement titanium pot cores. Every pot is built in Dongguan, Guangdong, China — send us your wire size, part and pot dimensions for a quotation.
Product Details
Overall view

Working position

Pot and control detail
Photographs are of the standard model. The pot size and the voltage are set to your order.
Product Demo Video
Contact us for a live working video of this pot on your wire or part.
Application ScenariosWire & Cable Ends Stranded wire ends and lugs are dipped by hand; the pot holds a large enough bath that a whole bundle can go in at once. Transformer & Inductor Pins Pin rows are dipped by hand for repair lots and small batches, or where the part cannot be held in a machine fixture. Mixed Part Numbers Where several different parts run through one bench, a hand pot needs no fixture change between them. Re-Tinning & Rework Re-tinning soldering iron tips, re-coating oxidised leads and stripping enamel by dipping, all on the same pot. How To UsePlace the pot on a level, heat-resistant bench and keep the working area dry.
Set the temperature on the inverter controller and let the pot reach it before adding solder.
Add lead-free solder bar until the bath covers the pot floor at the depth you need; the level drops as you work, so top it up through the shift.
Skim the oxide skin into the 40 × 40 mm dross box before the first dip and again whenever it builds up.
Apply flux to the wire end or pin group, then dip it squarely and lift it straight out.
Check the tinned length against the drawing and adjust the temperature or dipping time.
Switch off and let it cool before emptying or cleaning the pot.
⚠ Safety notice: molten solder is hot enough to cause severe burns — never reach over the pot, keep the bench dry (molten solder and water contact can cause splatter), wear heat-resistant gloves and eye protection, work in a ventilated area, and isolate the power supply before any service.Frequently Asked QuestionsQ1: What is a Lead-Free Solder Pot?
It is a bench-top heated pot that holds a bath of molten lead-free solder, into which wire ends and component pins are dipped by hand. This ceramic-heater version uses a titanium alloy pot and a ceramic heating tube. The same pot is also called a lead-free soldering pot, a lead-free solder bath or a lead-free tin pot — all these names refer to the same pot.
Q2: Why is the pot made of titanium alloy?
Lead-free (SAC) solder corrodes cast iron and plain stainless steel pots quickly. Titanium alloy resists that attack, so a titanium pot holds up far longer on lead-free work even though it costs more up front.
Q3: What does "ceramic heating tube" mean here?
The heater element is a ceramic-type heating tube rather than a bare metal tube. It spreads heat across the pot floor instead of concentrating it under one point, which keeps the solder bath at a more even temperature.
Q4: What sizes and power ratings are available?
Twelve sizes are held as stock, from 80 × 80 × 50 mm up to 400 × 135 × 50 mm inner dimensions, at 500 - 2000 W and 110 - 220 V / 50 Hz. Any other pot size is built to order from your inner length, width and depth.
Q5: How do I control the temperature?
Temperature is set with stepless inverter control — you dial the running temperature you want and the controller holds it, with no fixed steps between low and high.
Q6: Which industries use a pot like this?
Wire and cable assembly, transformer and inductor making, terminal and lug production, and repair or rework benches — wherever leads must be tinned by hand in small batches or in mixed part numbers.
Need a lead-free solder pot built to your pot size?Titanium alloy pot · Ceramic heating tube · 500 - 2000 W · 110 - 220 V / 50 Hz · 12 stock sizes, more to order · OEM / ODM available · Factory direct from Dongguan, ChinaGet a Quote
Verwandte Produkte
Ultrasonic Solder Pot FD-20014070C | Flux-Free Tinning Machine 200x140 mm Bath
Ultrasonic solder pot FD-20014070C, 200x...
Ultrasonic Solder Pot FD-14014070C | Flux-Free Tinning Machine 140x140 mm Bath
Ultrasonic solder pot FD-14014070C, 140x...
Ultrasonic Solder Pot FD-12012060C | Flux-Free Tinning Machine 120x120 mm Bath
Ultrasonic solder pot FD-12012060C, 120x...
Stainless Steel Explosion-Proof Industrial Oven FD1200800800FBB
Stainless Steel Explosion-Proof Industri...
Produkt-Anfrage
Bitte hinterlassen Sie Ihre Nachricht, wir werden uns nach Erhalt schnell mit Ihnen in Verbindung setzen, vielen Dank für Ihre Unterstützung!
Häufiges Problem
Q
Was sind die Merkmale der Zigarettenschachtel dreidimensionale Verpackungsmaschine?
A
1. Es besteht keine Notwendigkeit, die Höhe der Arbeitsplatten auf beiden Seiten der Maschine einzustellen, wenn die Form gewechselt wird, und es besteht keine Notwendigkeit, die Auslasskette zu demontieren und zu montieren oder den Trichter zu setzen, was die vierstündige Formwechselzeit der traditionellen Maschine auf nur 30 Minuten verkürzt.
2. Durch den neuen Doppelversicherungsmechanismus muss die Maschine nicht abgeschaltet werden, wenn sie nicht synchron läuft, und es werden auch keine anderen Teile beschädigt.
3. Die originale Einweg-Handkurbelvorrichtung verhindert, dass die Maschine rückwärts wackelt, und das Handrad dreht sich während des Betriebs nicht, was den Bediener sicherer macht.
4. Das neue Doppelrotationsfolienschneidemesser kann sicherstellen, dass die Maschine viele Jahre lang ohne Schärföffnung ununterbrochen verwendet werden kann, wodurch der Mangel überwunden wird, dass die traditionelle feste Einzelrotationsfolienschneidklinge leicht zu verschleißen ist.
Q
Automatische Poker transparente Folie dreidimensionale Verpackungsmaschine Verpackungsprodukte?
A
Automatische Poker transparente Folie dreidimensionale Verpackungsmaschine ist vor allem geeignet für Bulk-Poker, komprimierte Kekse, Sachima, Aufkleber, Haftnotizen, Waffel Kekse und andere Bulk-oder Multi-Objekt-Sammlung von dreidimensionalen Verpackungen.
E-Mail Adresse:
Hotline:
English
繁体中文
简体中文
Deutsch
Tiếng Việt


